Differences

This shows you the differences between two versions of the page.

--- oxygen:oxygenspecs [2022/08/30 11:10] – [Personality Board Specifications] bhuey
+++ oxygen:oxygenspecs [2023/01/29 08:28] (current) – bhuey
@@ Line 122: / Line 122: @@
 |  12  |  JTAG TMSn  |  Input  |  3.3V  |
 \\
-The header is recessed into the case and can be difficult to access. For this reason, RWT recommends using a header extension such as the Samtec [[https://www.samtec.com/products/esq-106-44-l-d|ESQ-106-44-L-D]]. For console port and JTAG access, the [[https://shop.trenz-electronic.de/en/TE0790-03-XMOD-FTDI-JTAG-Adapter-Xilinx-compatible|TE0790]] by Trenz Electronics is recommended as it is compatible with Xilinx software tools. If used, the TE0790 should be connected to the extended header in the following orientation.
+The header is recessed into the case and can be difficult to access. For this reason, RWT includes a header extension ([[https://www.samtec.com/products/esq-106-44-l-d|ESQ-106-44-L-D]]) in the kit. For console port and JTAG access, the [[https://shop.trenz-electronic.de/en/TE0790-03-XMOD-FTDI-JTAG-Adapter-Xilinx-compatible|TE0790]] by Trenz Electronics is recommended as it is compatible with Xilinx software tools. If used, the TE0790 should be connected to the extended header in the following orientation.
 {{oxygen:trenzmodulehookup.jpg?nolink&925}}
-For simple console port access without JTAG programming, a simple USB to UART adapter can be used. Examples of these include the [[https://www.adafruit.com/product/5335|Adafruit CP2102N Friend]], [[https://www.sparkfun.com/products/18289|SparkFun Electronics KIT-18289]], and [[https://ftdichip.com/products/ttl-232rg-vsw3v3-we/|FTDI TTL-232RG-VSW3V3-WE]].
+For simple console port access without JTAG programming, a simple USB to UART adapter can be used. Examples of these include the [[https://www.sparkfun.com/products/14050|SparkFun Electronics CH340G Dev 14050]], [[https://www.sparkfun.com/products/15096|SparkFun Electronics CH340C Dev 15096]], and [[https://ftdichip.com/products/ttl-232rg-vsw3v3-we/|FTDI TTL-232RG-VSW3V3-WE]].
 **The console UART port operates at 115,200 bps, 8 data bits, no parity, 1 stop bit, and no flow control.**
+Details on how to use these adapters with Oxygen can be found {{oxygen:oxygen_linux_serial_boot_adapters_-_5-25-2022.pdf|here}}.
 \\
 \\
@@ Line 139: / Line 141: @@
 \\
-These boards can be built in either the {{oxygen:rwt_rf_personality_standard_pcb_drawing.pdf|standard personality board format}}, or in an {{oxygen:rwt_rf_personality_extended_pcb_drawing.pdf|extended personality board format}} if more pcb surface area is needed.
+These boards can be built in either the {{oxygen:rwt_rf_personality_standard_pcb_drawing_v2.pdf|standard personality board format}}, or in an {{oxygen:rwt_rf_personality_extended_pcb_drawing_v2.pdf|extended personality board format}} if more pcb surface area is needed for components. A {{oxygen:rwt_rf_personality_schematic_template.pdf|schematic template}} has been created to illustrate the pinout of the mezzanine connectors, how these pin numbers map to the socket connectors, and the power rails that are available.
+A full pinout of JRF1 can be seen in the table below. The mezzanine connectors are hermaphroditic and the [[https://www.samtec.com/products/lss-120-03-f-dv-a-k|same part number]] is used on both the socket and the personality board. This results in even and odd pin numbers being swapped. For example, pin 1 on the socket will connect to pin 2 on the personality board. The JRF2 connector is optional and is currently used only for mechanical support and future expansion of the socket standard.  There are no signals on it.
+\\
+^  JRF1 \\ Pin Number \\ (Socket)  ^  Signal Name  ^  Direction  ^  FPGA Pin  ^  Signal Name \\ in Linux OS  ^  Logic Voltage  ^  Mating Connector \\ Pin Number \\ (Personality Board)  |
+|  1  |  12VDC  |  To Personality Board  |  -  |  -  |  -  |  2  |
+|  2  |  5VDC  |  To Personality Board  |  -  |  -  |  -  |  1  |
+|  3  |  12VDC  |  To Personality Board  |  -  |  -  |  -  |  4  |
+|  4  |  5VDC  |  To Personality Board  |  -  |  -  |  -  |  3  |
+|  5  |  GND  |  -  |  -  |  -  |  -  |  6  |
+|  6  |  GND  |  -  |  -  |  -  |  -  |  5  |
+|  7  |  3.3VDC  |  To Personality Board  |  -  |  -  |  -  |  8  |
+|  8  |  1.8VDC  |  To Personality Board  |  -  |  -  |  -  |  7  |
+|  9  |  3.3VDC  |  To Personality Board  |  -  |  -  |  -  |  10  |
+|  10  |  1.8VDC  |  To Personality Board  |  -  |  -  |  -  |  9  |
+|  11  |  GND  |  -  |  -  |  -  |  -  |  12  |
+|  12  |  GND  |  -  |  -  |  -  |  -  |  11  |
+|  13  |  NC  |  -  |  -  |  -  |  -  |  14  |
+|  14  |  NC  |  -  |  -  |  -  |  -  |  13  |
+|  15  |  NC  |  -  |  -  |  -  |  -  |  16  |
+|  16  |  NC  |  -  |  -  |  -  |  -  |  15  |
+|  17  |  I2C SCL  |  To Personality Board  |  MIO28  |  I2C Bus 0  |  3.3V  |  18  |
+|  18  |  NC  |  -  |  -  |  -  |  -  |  17  |
+|  19  |  I2C SDA  |  Bidirectional  |  MIO29  |  I2C Bus 0  |  3.3V  |  20  |
+|  20  |  NC  |  -  |  -  |  -  |  -  |  19  |
+|  21  |  GND  |  -  |  -  |  -  |  -  |  22  |
+|  22  |  GND  |  -  |  -  |  -  |  -  |  21  |
+|  23  |  NC  |  -  |  -  |  -  |  -  |  24  |
+|  24  |  NC  |  -  |  -  |  -  |  -  |  23  |
+|  25  |  NC  |  -  |  -  |  -  |  -  |  26  |
+|  26  |  NC  |  -  |  -  |  -  |  -  |  25  |
+|  27  |  GPIO 0  |  Bidirectional  |  B66_L6_N  |  GPIO94  |  1.8V  |  28  |
+|  28  |  RFIC GPO 0  |  To Personality Board  |  -  |  -  |  3.3V  |  27  |
+|  29  |  GPIO 1  |  Bidirectional  |  B66_L6_P  |  GPIO95  |  1.8V  |  30  |
+|  30  |  RFIC GPO 1  |  To Personality Board  |  -  |  -  |  3.3V  |  29  |
+|  31  |  GPIO 2  |  Bidirectional  |  B66_L22_P  |  GPIO96  |  1.8V  |  32  |
+|  32  |  RFIC GPO 2  |  To Personality Board  |  -  |  -  |  3.3V  |  31  |
+|  33  |  GPIO 3  |  Bidirectional  |  B66_L22_N  |  GPIO97  |  1.8V  |  34  |
+|  34  |  RFIC GPO 3  |  To Personality Board  |  -  |  -  |  3.3V  |  33  |
+|  35  |  GPIO 4  |  Bidirectional  |  B66_L4_P  |  GPIO98  |  1.8V  |  36  |
+|  36  |  NC  |  -  |  -  |  -  |  -  |  35  |
+|  37  |  GPIO 5  |  Bidirectional  |  B66_L4_N  |  GPIO99  |  1.8V  |  38  |
+|  38  |  NC  |  -  |  -  |  -  |  -  |  37  |
+|  39  |  GND  |  -  |  -  |  -  |  -  |  40  |
+|  40  |  GND  |  -  |  -  |  -  |  -  |  39  |